Knowledge Base
Cameras

Alta Camera Offline or Dark? Work Out If It's One Camera or Your Whole Network

Say it's Monday morning and Alta Video shows a red cross on the lobby camera. You walk over and it has no lights at all. Then you check the second floor. Those cameras show red crosses too, but their lights are on. Same problem, or two?

PAX Security6 min readNovember 19, 2026
Quick Answer

An offline Alta camera comes down to power or connection, and the lights tell you which. Start by counting. One camera with no lights usually points to power: the cable, the switch port or the injector feeding it. Several cameras down together, or cameras that have lights but a red cross, point to the switch, your internet or an Avigilon service issue. Check status.avigilon.com and note which cameras are affected. Avigilon's own first fix is a power cycle, but unplugging cables or rebooting a switch belongs to your installer or whoever runs your network, because it takes down everything else on that switch.

Key Takeaways

  • 1Count the dark cameras and write down where they are before anyone touches anything.
  • 2Check your internet and status.avigilon.com before blaming the camera.
  • 3Don't unplug cables or reboot switches yourself. That's for your installer or network admin.
  • 4Photograph the lights you can see from the floor. They help whoever fixes it.
  • 5Tell your installer about any power flicker or network change this week.

What to check from your desk when an Alta camera is offline

Everything here is look only.

  1. Count and name them. Open Alta Video, note every camera with a red cross, where it is, and roughly when it dropped.
  2. Check your own internet. Can a computer on the same network browse normally? Avigilon's guide for widespread outages asks this first.
  3. Check Avigilon's status page. Next, Avigilon says to look at status.avigilon.com. It lists Alta Video along with Avigilon's other services.
  4. Look at the camera from the floor. Lights on or off? A camera with no lights has lost power. A camera with lights and a red cross has power but isn't connecting.
  5. Ask whether other cameras on the same switch are down. Avigilon's diagnosis list asks exactly this. If you can see the switch without opening anything, look at whether other devices on it, like phones or door controllers, are down too.
  6. Think back. Any power flicker, storm, router or provider change, or firewall change? Anyone moving furniture or cables near a camera? Avigilon lists network and firewall changes and interrupted power among the causes of "Failed to communicate with the camera."

How to fix an offline Alta camera: Avigilon's order and who does each step

Avigilon's troubleshooting article lists the steps below. Customers shouldn't do the first two, and the rest take a tech.

  • Power cycle the camera's cable, or bounce its switch port
    • What it means: Cutting power to one camera, then restoring it
    • Who does it: Your installer or whoever runs your network
  • If several cameras are affected, reboot the switch
    • What it means: Restarts every device on that switch
    • Who does it: Your installer or whoever runs your network
  • Connect over USB-C, if your model has it
    • What it means: Checks whether the camera lights up on its own
    • Who does it: Your installer
  • If the camera lights up over USB-C, try PoE again on a different port, a different PoE switch, or an injector at the router
    • What it means: Rules out the port or switch
    • Who does it: Your installer
  • Still dark or still offline
    • What it means: Contact Avigilon Support
    • Who does it: Your installer or network admin

How a tech reads the lights

Many cameras get power and data over one network cable. That's PoE, short for power over Ethernet. So the lights tell a tech which half of the job failed.

No lights means the power half. A damaged cable, a worn connector, a dead port or a failed injector can leave a camera fully dark. A plain network problem usually doesn't, because the camera still has power. Lights with a red cross means the camera has power but can't reach Alta Video, so the tech looks at the connection side.

A tech's first look is the link and power lights at the switch port, and whether other devices on that switch dropped. One switch restarting after a power flicker looks like many cameras failing, and it's a very different fix. After that, the tech asks what changed. A router swap, a provider change or new firewall rules can all cut cameras off from the cloud, which is the story in our guide to cameras offline after a router or ISP change.

When it isn't your network

If Avigilon's status page shows no issue and your own network and internet are fine, it becomes a support case. Avigilon's guide for widespread outages says to contact Alta Video Support and include the deployment name, network test results and confirmation that the status pages are clear. That's a job for your installer.

One camera still dark, or several down?

If you're a PAX customer, call us and we'll talk through whether it's the camera, the cable, the switch or the network, and what to do next. If you're not, call anyway and we'll talk through your options. We work with Avigilon and cover security cameras for NYC businesses.

If the outage followed a blackout, see our guides to cameras offline after a power outage and what happens to your system when the power or internet goes out. Wondering why cameras run on a network cable at all? See wifi vs wired PoE cameras.

Call (855) 440-5353 or email info@paxsecurity.com.

Sources

Common Mistakes to Avoid

Rebooting the switch to see what happens. It drops everything else on that switch, such as recorders, door controllers and phones, and it makes it harder to tell what failed first.

Replacing the camera first. A bad cable or port can take the new one down too.

Assuming it will sort itself out. If it comes back, still ask why it dropped. A weak cable or port tends to fail again.

Updating or rebooting a camera in recovery mode. Avigilon says important diagnostic information can be overwritten. Leave it until Avigilon Support says what to do.

Frequently Asked Questions

What does "Failed to communicate with the camera" mean?

It means Alta Video can't reach that camera. Avigilon lists causes including a camera or switch that was disconnected, interrupted power, and network or firewall changes. Check whether other cameras on the same switch are affected, and tell your installer what changed.

Can a camera be offline when my internet is fine?

Yes. Besides power and network changes, Avigilon lists a camera put into ONVIF mode without being deleted and added again, and a camera that has Avigilon Unity or other firmware installed. If anyone has changed camera modes or firmware, tell your installer.

Should I call Avigilon or my installer?

Start with whoever installed or maintains your system. Avigilon asks support cases to include things like the deployment name and network test results, and your installer can gather them.

Not sure what your property needs?

PAX Security designs and installs security cameras, access control, intercom, and cabling systems for commercial and multifamily properties across New York City. Tell us about your building and we will give you a straight answer.

Call UsGet a Quote